Deep Pour Epoxy
DEEP POUR EPOXY 2-4” POURS WITH EASE
IMPORTANT! All epoxies HAVE to be shipped UPS Ground or FedEx due to limited HAZMAT requirements. If you have included pigments with your order, they will be shipped separately. NO FREE SHIPPING. We still honor free shipping on pigment orders over $49.00 domestic.
DESCRIPTION
Superclear 2.0 Liquid Glass Deep Pour Epoxy
Our Liquid Glass Deep Pour Epoxy is absolutely unparalleled with a deep pour capability of 2-4 inches and gives you unmatched industry performance, convenience by eliminating 75% of your work, and the clearest finish you can get on the market today!
FOOD SAFE ART RESIN CERTIFIED
MOST DURABLE EPOXY ON THE MARKET
– SuperClear 2.0 cures rock-hard, giving you unparalleled structural integrity, and is able to withstand years of wear & tear without a problem!
BUBBLE-LESS TECHNOLOGY
– Liquid Glass Epoxy is a low viscosity formulation that effortlessly allows for bubbles to rise to the surface as it cures. Giving you a crystal clear finish every time!
MADE IN THE USA
– Fiberglass Coatings, Inc. is based out of Saint Petersburg, FL and has been in business for over 60 years! We are proud to say we are made 100% in the USA!
DIRECTIONS
STEP 1:
Using the Coverage Chart, determine the amount of epoxy you will need for your project. Be sure to order SuperClear Table Top Epoxy for a seal coat to ensure best results!
STEP 2:
Ensure your working environment is clean, dry and at least 70 degrees for best results. Lay down a plastic sheeting below your project for a safe, easy cleanup. Make sure your surface is completely level, as the epoxy will self-level.
STEP 3:
Seal Coat – Be sure to clean the surface with Isopropyl Alcohol 90% + and apply your sealcoat with a brush, following all mixing directions for that product. Let it get tacky before pouring your deep pour. If the seal layer is fully cured, for best results, lightly sand the surface with 320 grit sandpaper and clean with Isopropyl Alcohol 90% +, and then pour the deep pour.
STEP 4:
Mixing Deep Pour – Measure 2 parts Resin to 1 part Activator and pour into a clean, dry bucket or cup. Stir the mixture for at least 5 minutes with either a stir stick (if mixing with a stir stick, do not mix more than 1 quart) or a drill mixer set to low. Ensure you are not whipping air into your epoxy. Be sure to scrape the sides and bottom to ensure all of your epoxy is properly mixed.
STEP 5:
Transfer contents to a new, clean, dry bucket or cup and continue mixing for 3 more minutes to ensure proper mixing, again scraping sides and bottom.
STEP 6:
Pour mixture directly into your mold at your desired depth. Do not scrape the bucket at this time. If you do, you risk scraping in unmixed material that has clung to the sides or bottom. This would result in soft spots and/or hotspots.
STEP 7:
Use a heat source, like a heat gun to remove any air bubbles. Start at 6” minimum above the surface and sweep back and forth until no bubbles remain. Do not leave the heat gun over the surface too long, if you do, it may result in surface distortions.
STEP 8:
Allow the surface to cure, up to 72 hours in a dust-free environment. The epoxy will start to get tacky after 24 hours but do not disturb for 72 hours to ensure a proper cure.
FAQS
HOW LONG DO I HAVE TO MIX IT?
– You need to stir it by hand for a minimum of 5 minutes, scraping the sides and bottom thoroughly throughout while mixing. When pouring, we do not recommend scraping the sides. Doing so can risk mixing in unmixed, unincorporated epoxy into your pour, thus creating curing issues.
HOW THICK CAN I POUR IT?
– You can pour up to 4” thick per pour, depending on ambient temperature and total mass. Much thicker than most competitors! The mass for a 4” pour varies depending on temperatures and conditions. If you have never poured a deep pour at 4”, we suggest you try it on a smaller scale to understand how it will cure in your particular environment.
HOW LONG DOES IT TAKE TO CURE?
– The product will begin to harden within the first 12-24 hours in ideal conditions, but takes 48-72 hours to completely cure, depending upon conditions like constant temperature, humidity, mass and airflow.
CAN I ADD ANOTHER LAYER TO THE SURFACE?
– Yes! Simply wait until the pour is tacky and nearly hard and pour your next layer. If the product is already hard, lightly sand with 220-320 grit sandpaper and wipe it down with Isopropyl Alcohol 90% or higher before adding additional layers, which helps with the adhesion between the two layers.
CAN I CLAMP DOWN MY WOOD TO PREVENT IT FROM FLOATING?
– While you can clamp down your wood during a deep pour, be sure not to clamp it too tightly. As the epoxy cures, the wood needs some room to flex while it turns from a liquid to a solid. Without room to flex, pressure will build in the epoxy, resulting in stress, increased heat, and even cracking. To avoid this, only finger tighten your C-Clamps or use light enough weights to keep the wood from floating.
CAN I MIX PIGMENT/DYE/MICA POWDER?
You can mix nearly all alcohol dye’s, mica powders, and liquid pigments with our product, not to exceed 12%. However, we do not recommend acrylic based colorants as they can negatively react with the epoxy.
DISCLAIMER
While our product can be used in a variety of applications, not all users or environments are the same. As such, specific directions for all individual users might not be addressed in the directions. If there are any questions that our directions do not answer, pertaining to the individual customer’s application, it is the customer’s sole responsibility to contact us directly with any technical questions and procedures prior to the application of the product. See below for various means to obtain further information and or contact us directly; we offer FAQs on our website and technical service via Email or phone Monday through Friday, 9am-4pm EST.
For more product information, please visit:
www.SuperEpoxySystems.com
(888) 849-0588
superclear@fgci.com
Temperature : Volume & Depth Info
Always pour in a temperature controlled environment. Ideal working temperatures are 70°F to 84°F, but this is dependent on the total volume and depth of the project. The greater the volume or thickness of the pour, the lower your temperatures should be.
ADDITIONAL INFORMATION
| Weight | N/A |
|---|---|
| Dimensions | N/A |
| Shelf Life |
Unopened: 6 – 12 months* *depending upon how the product is stored. |
Ships domestic via UPS Ground. International shipping via UPS. We do not ship via USPS.
You may also like
More from Epoxy Resin
Recently viewed